test/doc/source/manual_tests/installation_and_configuration/index.rst

Installation and Configuration

This test plan covers Installation and Configuration regression. It covers basic functionality for the following features:

• License
• Installation and commissioning
• Secure Boot
• tboot
• IPv4 and IPv6 installation

Overall Requirements

IP4 & IP6 system installed successful.

Test Cases

INSTALLATION_AND_CONFIGURATION_INSTALL_01

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALL_01

Test Title

test_AIO-DX https ipv4 install

Tags

P1, Installation and configuration, Regression, AUTOMATED

Test Objective

To ensure DX https ipv4 installation working well on StarlingX.

Test Pre-Conditions

NA

Test Steps

Install IPv4 DX system.

Expected Behaviour

Installation successfully.

INSTALLATION_AND_CONFIGURATION_INSTALL_02

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALL_02

Test Title

test_AIO-DX https ipv4 low-latency pxeboot_setup install

Tags

P1, Installation and configuration, Regression, AUTOMATED

Test Objective

To ensure DX https ipv4 low-latency installation working well on StarlingX.

Test Pre-Conditions

NA

Test Steps

Install DX https ipv4 low-latency system.

Expected Behaviour

Installation successfully.

INSTALLATION_AND_CONFIGURATION_INSTALL_03

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALL_03

Test Title

test_Standard https ipv4 install

Tags

P1, Installation and configuration, Regression, AUTOMATED

Test Objective

To ensure standard https ipv4 installation working well on StarlingX.

Test Pre-Conditions

NA

Test Steps

Install IPv4 standard system.

Expected Behaviour

Installation successfully.

INSTALLATION_AND_CONFIGURATION_INSTALL_04

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALL_04

Test Title

test_Standard https ipv6 install

Tags

P1, Installation and configuration, Regression, AUTOMATED

Test Objective

To ensure standard https ipv6 installation working well on StarlingX.

Test Pre-Conditions

NA

Test Steps

Install IPv6 standard system.

Expected Behaviour

Installation successfully.

INSTALLATION_AND_CONFIGURATION_LICENSE_05

Test ID

INSTALLATION_AND_CONFIGURATION_LICENSE_05

Test Title

test_Post install license-install with corrupted license file

Tags

P3, Installation and configuration, Regression

Test Objective

To ensure Post install license-install with corrupted license file working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

After config-controller, run "system license-install <license-file>" with corrupted license file

Expected Behaviour

Verification should fail and Error msg should be clearly addressed.

INSTALLATION_AND_CONFIGURATION_LICENSE_06

Test ID

INSTALLATION_AND_CONFIGURATION_LICENSE_06

Test Title

test Post install license-install with expired license file

Tags

P2, Installation and configuration, Regression

Test Objective

To ensure Post install license-install with expired license file working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

After config-controller, run "system license-install <license-file>" with expired license file.

Expected Behaviour

Verification should fail and Error msg should be clearly addressed.

INSTALLATION_AND_CONFIGURATION_LICENSE_07

Test ID

INSTALLATION_AND_CONFIGURATION_LICENSE_07

Test Title

test_Run lab_setup with missing license file

Tags

P2, Installation and configuration, Regression

Test Objective

To ensure running lab_setup with missing license file working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

1. run config_controller without license file config complete
2. run lab_setup.sh without license operation: "proper warning popup like "license missing..."

Expected Behaviour

As above.

INSTALLATION_AND_CONFIGURATION_LICENSE_08

Test ID

INSTALLATION_AND_CONFIGURATION_LICENSE_08

Test Title

test_Verify License configuration on configui tool

Tags

P1, Installation and configuration, Regression

Test Objective

To Verify License configuration on configui tool working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

Using config_gui to generate config file.

Expected Behaviour

There is no license related questions asked.

INSTALLATION_AND_CONFIGURATION_LICENSE_09

Test ID

INSTALLATION_AND_CONFIGURATION_LICENSE_09

Test Title

test_Verify post install license-install

Tags

P1, Installation and configuration, Regression

Test Objective

To test_Verify post install license file working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

1. Run "config-controller" without config.ini. Config process should run through.
2. Run "system license-install <license-file>". License installed as expected.

Expected Behaviour

As above.

INSTALLATION_AND_CONFIGURATION_INSTALLATION_10

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALLATION_10

Test Title

test Installation and Commissioning: Attempt to add hosts prior to controller-0 unlock (negative test)

Tags

P4, Installation and configuration, Regression

Test Objective

To test Attempting to add hosts prior to controller-0 unlock working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

1. Install controller-0. Controller-0 should show offline very briefly and then show locked-online.

2. While controller-0 is locked, attempt to add hosts via system host-bulk-add(CLI). This should fail with "Bulk_add requires enabled controller. Please unlock controller-0, wait for it to enable and then retry.

3. While controller-0 is locked, attempt to add hosts via horizon. This should fail with Provisioning request for new host '<mac address> is not permitted while there is no unlocked-enabled controller. Unlock controller-0, wait for it to enable and then retry.

4. While controller-0 is locked, attempt to add hosts via CLI via system host-update. This should fail with:

   Provisioning request for new host <mac address> is not permitted while there is no unlocked-enabled controller.

5. Unlock controller-0, wait for it to enable and then retry.

Expected Behaviour

As above.

INSTALLATION_AND_CONFIGURATION_INSTALLATION_11

Test ID

INSTALLATION_AND_CONFIGURATION_INSTALLATION_11

Test Title

test_Installation and Commissioning: Validate controller-0 state after unlock

Tags

P4, Installation and configuration, Regression, AUTOMATED

Test Objective

To test Validating controller-0 state after unlock working as expected on StarlingX.

Test Pre-Conditions

NA

Test Steps

1. Install controller-0 (on an AIO-SX or AIO-DX system). The controller should be locked-online.
2. Unlock controller-0. Validate the host status in horizon reports: "Unlocking active controller" please stand-by while it reboots.
3. Validate that the controller only reboots once after unlock

Expected Behaviour

As above.

INSTALLATION_AND_CONFIGURATION_TBOOT_12

Test ID

INSTALLATION_AND_CONFIGURATION_TBOOT_12

Test Title

test_01: SB(Dis) ESP(En) Con0(UEFI,TXT on) Con1(UEFI TXT on) Com(UEFI TXT on) Stg(UEFI TXT on)

Tags

P4, Installation and configuration, Regression

Test Objective

To ensure the tboot configuration as title shown working well on StartlingX.

Test Pre-Conditions

NA

Test Steps

01: SB(Dis) ESP(En) Con0(UEFI,TXT on) Con1(UEFI TXT on) Com(UEFI TXT on) Stg(UEFI TXT on). All nodes: TBoot functional

Expected Behaviour

System boot successfully.

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_13

Test ID

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_13

Test Title

test_UEFI Secure Boot enabled TiS WRS Cert in firmware install compute successful

Tags

P2, Installation and configuration, Regression

Test Objective

To ensure the security boot configuration as title shown working well on StartlingX.

Test Pre-Conditions

NA

Test Steps

1. Enable UEFI secure boot on compute host.
2. Install TiS WRS cert from firmware of compute host.
3. Attempt to install compute host from controller-0

Expected Behaviour

Compute host must install successfully from controller-0 when TiS WRS cert is present in compute host's firmware.

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_14

Test ID

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_14

Test Title

test_UEFI Secure Boot enabled TiS WRS Cert in firmware install controller-1 successful

Tags

P2, Installation and configuration, Regression

Testcase Objective

To ensure the security boot configuration as title shown working well on StartlingX.

Test Pre-Conditions

NA

Test Steps

1. Enable UEFI secure boot on controller-1.
2. Install TiS WRS cert from firmware of controller-1.
3. Attempt to install controller-1 from controller-0.

Expected Behaviour

Controller-1 must install successfully from controller-0 when TiS WRS cert is present in controller-1 firmware.

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_15

Test ID

INSTALLATION_AND_CONFIGURATION_SECURITYBOOT_15

Test Title

test_UEFI Secure Boot enabled TiS WRS Cert in firmware install low latency CPE controller-0 successful

Tags

P2, Installation and configuration, Regression

Test Objective

To ensure the security boot configuration as title shown working well on StartlingX.

Test Pre-Conditions

NA

Test Steps

1. Enable UEFI secure boot on CPE controller-0 host.
2. Install TiS WRS cert into firmware.
3. Attempt to install a low latency controller-0 CPE host.

Expected Behaviour

Low latency CPE controller-0 host must install successfully in UEFI secure boot mode when TiS WRS cert is present in firmware.